ca888亚洲城

你的当前位置是:ca888亚洲城 > 资讯中心 >

资讯中心

碗型轴承架


发布时间:2018-06-13 发布人:亚洲城ca88唯一官网

碗型轴承架是装有碗型瓦的碗型瓦架支撑主轴部并把破碎力传递给机架,通过过盈配合和碗型瓦架四周的螺钉使其紧紧地固结在机架上。圆锥破碗型瓦装在碗型瓦架上,给躯体提供一个支撑轴承面。碗型瓦支撑球形面由通过主轴中心和躯体的油孔提供充足的润滑。碗型瓦架上焊有挡圈,防止碗型瓦上表面的循环油益出流到密封装置上。碗型瓦上的油沟碗型瓦与碗型瓦架上的一组孔可使润滑油流回液压圆锥破碎机内部。

The bowl type bearing rack is a bowl type tile support spindle with a bowl shaped tile and passes the crushing force to the frame. Through the interference fit and the screws around the bowl type tile frame, it is tightly consolidated on the frame. The cone shaped bowl shaped tile is mounted on the bowl type tile rack to provide a supporting bearing surface for the body. The bowl shape tile supports the spherical surface to provide adequate lubrication through the oil hole through the spindle center and the body. The bowl type tile frame is welded with a retaining ring to prevent the circulating oil on the upper surface of the bowl tile from flowing to the sealing device. A bowl of tile on the bowl tile and a hole on the bowl tile can make the lubricating oil flow back into the hydraulic cone crusher.

碗型轴承架

碗型轴承架基本步骤:

1、把碗型轴承架放在机架上,并将碗型瓦架上的孔和机架上的螺纹孔对正。为保证能够正确安装,两者各有一组孔是偏置的。

2、将内六角螺栓穿过碗型瓦架上的孔,拧入机架上的孔内。

3、为防止别劲,要轮流把紧螺栓,每次的使力不要过大。如果过盈量为上限,用螺栓压入碗型瓦架很困难时,可以将机架上与碗型瓦架的配合面进行加热使之高于环境温度400C左右。

4、把紧全部螺栓,确保碗型瓦架与机架贴合面完全贴合。

The basic steps of the bowl type bearing frame are:

1, put the bowl type bearing frame on the rack, and correct the holes on the bowl type tile rack and the thread holes on the rack. To ensure proper installation, each group has a set of holes that are biased.

2. Screw the inner six bolts through the hole of the bowl type tile rack and screw into the hole on the rack.

3, in order to prevent the strength, turn the bolts tightly and do not exert too much force each time. If the interference amount is the upper limit, it is difficult to press the bowl type tile with the bolt, so it can be heated to the bowl type tile frame to be heated to the ambient temperature of 400C.

4. Tighten all the bolts to ensure that the bowl type tile rack is completely attached to the rack surface.

1.碗形轴承安装前的准备工作:

A清除油槽及油孔内的杂物;

B检查防尘圈和档油圈有无碰坏或变形现象;

C检查各加工表面有无损坏之处,如有损坏应马上进行修理。

2.碗形轴承架应与底座配合紧密,并用塞尺检查水平接触面得紧密情况。

3.碗形轴承安装好后,马上用盖板将碗形瓦盖好装破碎圆锥时再将盖板拿下。

4.安装碗形轴承时应注意保护进水管、排水道、挡油圈、防尘圈,以免装入时碰坏。

1. preparatory work before the installation of the bowl bearing:

A clears the sundries in the oil tank and the oil hole.

B check whether dustproof ring and oil ring are damaged or deformed.

C check whether there are any damage to the machined surface. If there is any damage, repair should be carried out immediately.

2. the bowl bearing bracket should be closely matched with the base, and the horizontal contact surface must be closely checked with a feeler gauge.

3. when the bowl shaped bearing is installed, immediately cover the bowl shaped tile with the cover plate to crush the cone, and then take the cover plate off.

4. when installing bowl shaped bearing, attention should be paid to protecting water inlet pipe, drainage channel, oil retaining ring and dustproof ring, so as to avoid damage when loading.



破碎机常识推荐

破碎机设备推荐

XML 地图 | Sitemap 地图