ca888亚洲城

你的当前位置是:ca888亚洲城 > 资讯中心 >

资讯中心

破碎机出料不达标的原因分析


发布时间:2018-08-30 发布人:亚洲城ca88唯一官网

ca888亚洲城在使用的过程中,很容易会出现各种问题,无论是产量下降的原因分析,或者是解决出料不合理的现象,都是生产中重要的操作,那么是很容易出现设备的损坏的,这里是来先容一下出料不达标的现象是哪些原因引起的问题。

Crusher manufacturers in the use of the process, it is easy to appear a variety of problems, whether it is the reason for the decline in output analysis, or to solve the unreasonable phenomenon of discharging, is an important operation in production, so it is easy to damage equipment, here is to introduce the phenomenon of discharging is not up to standard what causes. Problems arise.

破碎机出料不达标的原因分析

原因一、破碎比
破碎比指的是进口料和破碎后的成品粒径的比值,比值越大,破碎比也越大,反之亦然,对于破碎机的生产过程来说,破碎比大的话针片状含量增加,所以生产中,对于破碎比的调节是保证出料的重要措施,当然破碎比过小也是不行的,这会造成整个系统产量的降低、内循环量增加,使得破碎机磨损增加,所以破碎比的选择需要适当;
Reason 1, crushing ratio
Crushing ratio refers to the ratio of the particle size of the imported material to the finished product after crushing. The bigger the ratio, the bigger the crushing ratio, and vice versa. For the crusher production process, the larger the crushing ratio, the higher the needle flake content, so in production, the adjustment of the crushing ratio is an important measure to ensure the discharge, of course, the smaller the crushing ratio. No, it will reduce the output of the whole system, increase the internal circulation, make the crusher wear increased, so the choice of crushing ratio needs to be appropriate;
原因二、进料粒度
对于破碎机来说,不同的类型或者不同的型号可以加工的入料尺寸大小是不同的,如果进料粒度不合适的话,也会造成出料品质不达标的现象,比如说当进料粒度由100mm降低到50mm时,成品料中针片状含量下降38%,所以进料粒度一定要符合生产设备的要求;
Cause two. Feed size
For crushers, different types or different models can be processed into different sizes of the feed, if the size of the feed is not appropriate, it will also cause the quality of the discharged material is not up to standard, for example, when the size of the feed from 100 mm to 50 mm, the finished product of the needle flake content decreased by 38%, so the size of the feed grain. Must comply with the requirements of production equipment.
 原因三、循环负荷
破碎机的工作过程是在一个闭路循环中进行的,调大排料口,增加循环中的负荷,石料粒形会变好,在整个过程中,由于循环负荷加大,系统中各设备的磨损增加,但当排料口调大后,主破碎电机的负荷可降低,成品料粒形变好,因此在生产中,对于循环负荷的调整是很重要的;
Reason three, cyclic load
The working process of the crusher is carried out in a closed-circuit cycle. By adjusting the discharge port and increasing the load in the cycle, the grain shape of the stone will be better. In the whole process, the wear of the equipment in the system will be increased due to the increase of the cyclic load. But when the discharge port is increased, the load of the main crushing motor will be reduced and the grain shape of the finished product will be changed. So, in production, the adjustment of cycle load is very important.
 原因四、开路和闭路循环
在破碎机的生产中,循环分开路循环和闭路循环,前者称为先筛后碎,后者称为先碎后筛,先筛后碎是指把经一级破碎后的料先经过成品筛筛分后再进入二级破碎进料口进行破碎,这样成品料的产量增加,针片状含量也增加了,先碎后筛是指把一级破碎的料全部进入二级破碎机进料口,进行复破后再进成品筛进行筛分,整个系统是一个封闭系统,没有破碎料流失,循环负荷较大,但产品粒形好,在破碎机的实际生产中,可以根据生产的需求进行开路或者闭路循环的选择;
Reason four, open circuit and closed cycle.
In the production of crusher, the former is called first screening and then crushing, the latter is called first crushing and then screening, first screening and then crushing refers to the material after the first crushing through the screening of finished products and then into the second crushing inlet for crushing, so that the output of finished products increased, the content of needle flakes also increased. First crushing and then screening refers to the first crushing material into the second crusher inlet, after re-breaking screening finished products, the entire system is a closed system, there is no loss of crushing material, cyclic load is large, but the product has good granularity, in the actual production of crusher, can be opened according to production needs. The choice of road or closed cycle.
    以上这些破碎机出料不达标的原因分析,对于这一问题的分析主要是从四个方面进行的,分布是破碎比、进料粒度、循环负荷以及开路和闭路循环,ca888亚洲城在实际的生产中,需要根据生产的要求适当的选择每一个方面的因素,也就是大家所说的对症下药,找到合适正确的处理方法肯定是会事半功倍的。
These crushers are not up to standard for the reasons for the analysis of this problem is mainly carried out from four aspects, the distribution is crushing ratio, feed size, cycle load and open and closed circuit cycle, crusher manufacturers in actual production, according to the production requirements of the appropriate selection of each aspect of the cause Su, which is what we call symptomatic medicine, is bound to get twice the result with half the effort in finding the right treatment.

破碎机常识推荐

破碎机设备推荐

XML 地图 | Sitemap 地图